MATERIAL SAFETY DATA SHEET

HILTI, INC.:
P.O. Box 21148
Tulsa, OK 74121
Ph: 1 800 879 6000
Emergency No.: 1 800 879 4444

PRODUCT NAME: CS 300 EP Floor Joint Sealant, Part A

DESCRIPTION: Epoxy/polyurethane resin

INGREDIENTS AND EXPOSURE LIMITS

* NJ TSRN 31765300002-6184p

PEL = OSHA Permissible Exposure Limit. TLV = ACGIH Threshold Limit Value. These are 8 hour time-weighted averages unless otherwise indicated by "C" (Ceiling) or "STEL" (Short Term Exposure Limit). NE = None Established. NA = Not Applicable.

PHYSICAL DATA

FIRE AND EXPLOSION HAZARD DATA

FLASH POINT: > 200 F setaflash FLAMMABLE LIMITS: Not Applicable

EXTINGUISHING MEDIA: Water, CO₂, Dry Chemical, Foam

SPECIAL FIRE FIGHTING PROCEDURES: Wear full protective clothing. A NIOSH-approved self-contained breathing apparatus (SCBA) should be worn when fighting fires involving chemicals.

UNUSUAL FIRE AND EXPLOSION HAZARDS: None known. Thermal decomposition products can be produced under fire conditions. See below.

REACTIVITY DATA

STABILITY: Stable

INCOMPATIBILITY: Strong acids, peroxides and other oxidizing agents

HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition can yield carbon dioxide and/or carbon monoxide.

HAZARDOUS POLYMERIZATION: Will not occur.

CONDITIONS TO AVOID: Avoid temperature extremes which could shorten the shelf-life of this product; i.e. below freezing and above 100° F. (See handling and storage requirements below).

HEALTH HAZARD DATA

KNOWN HAZARDS: Acute: Eye and skin irritation. Chronic: Sensitization is possible.

CARCINOGENICITY: No ingredients are classified by IARC, NTP, or OSHA as known or potential carcinogens.

PRIMARY ROUTES OF EXPOSURE: Dermal. Inhalation.

SIGNS AND SYMPTOMS OF EXPOSURE: Eyes - Can cause irritation; corneal injury is unlikely. Skin - Can cause irritation. An allergic skin reaction (e.g. rash, itching, reddening) can occur with some individuals. Inhalation - No effects expected. Exposure to heated vapors can cause irritation. Ingestion - Not considered to be a route of exposure. Effects of ingestion have not been determined

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Eye, skin, and respiratory conditions.

EMERGENCY AND FIRST AID PROCEDURES

EYES: Wash immediately with large amounts of clean water. Seek medical attention if irritation persists.

SKIN: Wash with soap and water.

INHALATION: Move victim to fresh air. Give oxygen and/or artificial respiration if needed. Call a physician.

INGESTION: If conscious, give plenty of water to drink. Do not induce vomiting unless large amounts are ingested. Never give anything by mouth to an unconscious person Contact a physician immediately.

OTHER: Referral to a physician is recommended if there is any question about the seriousness of the injury/exposure.

CONTROL MEASURES AND PERSONAL PROTECTIVE EQUIPMENT

VENTILATION: General (i.e., natural or mechanically induced fresh air movements that maintain vapor concentrations below recommended exposure limits).

EYE PROTECTION: Safety glasses with side shields; chemical goggles while mixing.

SKIN PROTECTION: Cloth may be suitable; impervious (neoprene or rubber) gloves are recommended.

RESPIRATORY PROTECTION: Not normally required. Where ventilation is inadequate to control vapors, use a NIOSH-approved respirator with organic vapor cartridges. Never enter a confined space without an appropriate air supplied respirator.

PRECAUTIONS FOR SAFE HANDLING AND USE

HANDLING AND STORING PRECAUTIONS: Store in a cool, dry area. Keep from freezing. Store between 40° and 100° F. For industrial use only. Keep out of reach of children. Use with adequate ventilation. Do not get into the eyes. Avoid prolonged or repeated contact with the skin. Practice good hygiene; i.e. wash after using and before eating or smoking.

SPILL PROCEDURES: Take up with an absorbent material and place in a container for proper disposal in accordance with all applicable local, state, or federal requirements. Not considered to be a hazardous waste according to EPA definitions.

REGULATORY INFORMATION

HAZARD COMMUNICATION: This MSDS has been prepared in accordance with the federal OSHA Hazard Communication Standard.

HMIS CODES: Health 2, Flammability 1, Reactivity 0, PPE B

DOT SHIPPING NAME: Not regulated

TSCA INVENTORY STATUS: Chemical components listed on TSCA inventory.

SARA TITLE III, SECTION 313: This product does not contain any toxic chemicals which are subject to reporting under Section 313 of SARA Title III (40 CFR Part 372).

WASTE DISPOSAL METHODS: Consult with regulatory agencies or corporate personnel for disposal methods that comply with local, state, and federal health and environmental regulations.

HEALTH / SAFETY CONTACTS:
Steve Gerrard (x6309)
Jerry Metcalf (x6704)

The information and recommendations contained herein are based upon data believed to be correct; however, no guarantee or warranty of any kind expressed or implied is made with respect to the information provided

MATERIAL SAFETY DATA SHEET

HILTI, INC.:
P.O. Box 21148
Tulsa, OK 74121
Ph: 1 800 879 6000
Emergency No.: 1 800 879 4444

PRODUCT NAME: CS 300 EP Floor Joint Sealant, Part B

DESCRIPTION: Amine hardener for CS 300 EP epoxy sealant

INGREDIENTS AND EXPOSURE LIMITS

PEL = OSHA Permissible Exposure Limit. TLV = ACGIH Threshold Limit Value. These are 8 hour time-weighted averages unless otherwise indicated by "C" (Ceiling) or "STEL" (Short Term Exposure Limit). NE = None Established. NA = Not Applicable.

PHYSICAL DATA

FIRE AND EXPLOSION HAZARD DATA

FLASH POINT: > 200 F setaflash FLAMMABLE LIMITS: Not Applicable

EXTINGUISHING MEDIA: Water, CO₂, Dry Chemical, Foam

SPECIAL FIRE FIGHTING PROCEDURES: Wear full protective clothing. A NIOSH-approved self-contained breathing apparatus (SCBA) should be worn when fighting fires involving chemicals.

UNUSUAL FIRE AND EXPLOSION HAZARDS: None known. Thermal decomposition products can be produced under fire conditions. See below.

REACTIVITY DATA

STABILITY: Stable

INCOMPATIBILITY: Strong acids, peroxides and other oxidizing agents

HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition can yield CO, CO₂, aldehydes and acid gases

HAZARDOUS POLYMERIZATION: Will not occur.

CONDITIONS TO AVOID: Avoid temperature extremes which could shorten the shelf-life of this product; i.e. below freezing and above 100° F. (See handling and storage requirements).

HEALTH HAZARD DATA

KNOWN HAZARDS: Acute: Corrosive. Causes eye and skin burns. Chronic: None known.

CARCINOGENICITY: No ingredients are classified by IARC, NTP, or OSHA as known or potential carcinogens.

PRIMARY ROUTES OF EXPOSURE: Dermal. Inhalation.

SIGNS AND SYMPTOMS OF EXPOSURE: Eyes - Causes eye burns. Skin - Causes skin burns. Inhalation - Can cause irritation. Ingestion - Not considered to be a route of exposure. Will cause burns.

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Eye, skin, and respiratory conditions.

EMERGENCY AND FIRST AID PROCEDURES

EYES: Wash immediately with clean water for at least 15 minutes. Seek medical attention.

SKIN: Flush skin immediately with large amounts of water.

INHALATION: Move victim to fresh air. Give oxygen and/or artificial respiration if needed. Call a physician.

INGESTION: If conscious, give plenty of water to drink. Do not induce vomiting unless large amounts are ingested. Never give anything by mouth to an unconscious person Contact a physician immediately.

OTHER: Referral to a physician is recommended if there is any question about the seriousness of the injury/exposure.

CONTROL MEASURES AND PERSONAL PROTECTIVE EQUIPMENT

VENTILATION: General (i.e., natural or mechanically induced fresh air movements that maintain vapor concentrations below recommended exposure limits).

EYE PROTECTION: Chemical goggles

SKIN PROTECTION: Cloth may be suitable; impervious (neoprene or rubber) gloves are recommended.

RESPIRATORY PROTECTION: Not normally required. Where ventilation is inadequate to control vapors, use a NIOSH-approved respirator with organic vapor cartridges. Never enter a confined space without an appropriate air supplied respirator.

PRECAUTIONS FOR SAFE HANDLING AND USE

HANDLING AND STORING PRECAUTIONS: Store in a cool, dry area. Keep from freezing. Store between 40° and 100° F. For industrial use only. Keep out of reach of children. Use with adequate ventilation. Keep container closed when not in use. Do not get into the eyes. Avoid contact with the skin. Practice good hygiene; i.e. wash after using and before eating or smoking.

SPILL PROCEDURES: Take up with an absorbent material and place in a container for proper disposal in accordance with all applicable local, state, or federal requirements. Not considered to be a hazardous waste according to EPA definitions.

REGULATORY INFORMATION

HAZARD COMMUNICATION: This MSDS has been prepared in accordance with the federal OSHA Hazard Communication Standard.

HMIS CODES: Health 3, Flammability 1, Reactivity 0, PPE B

DOT SHIPPING NAME: Corrosive liquid, n.o.s., (contains n-aminoethylpiperazine, nonyl phenol), Class 8, UN 1760, PG III, Ltd. Qty.

TSCA INVENTORY STATUS: Chemical components listed on TSCA inventory.

SARA TITLE III, SECTION 313: This product contains 9% dibutyl phthalate (CAS 84-74-2) which is subject to reporting under Section 313 of SARA Title III (40 CFR Part 372).

WASTE DISPOSAL METHODS: Consult with regulatory agencies or corporate personnel for disposal methods that comply with local, state, and federal health and environmental regulations.

HEALTH / SAFETY CONTACTS:
Steve Gerrard (x6309)
Jerry Metcalf (x6704)

The information and recommendations contained herein are based upon data believed to be correct; however, no guarantee or warranty of any kind expressed or implied is made with respect to the information provided